A tripped breaker or a dead outlet is usually what starts the call. Somebody in Edmonds resets the breaker, it holds for a day, then trips again. Or an outlet stops working and the one next to it is fine. Those symptoms feel minor, but they often point to something worth looking at properly: an overloaded circuit, a failing breaker, a GFCI that has stopped tripping correctly, or wiring that has been spliced and re-spliced over the years. The job that looks like a quick fix sometimes turns out to have a longer story behind it.
When that happens, we say so before any work starts. We scope the job on the phone, and if what we find when we arrive changes the picture, we explain what changed and confirm a new price before we go further. Homeowners and property managers in Edmonds call us for repairs, panel work, new circuits, and safety inspections, and the process is the same for all of them.
Call (425) 928-9789 and we will tell you what the job involves and what it costs. We are available every day from 8:30 AM to 11:00 PM.
Homes in a city this size carry a wide range of electrical histories. Some have been updated properly over the years. Others have had circuits added without a permit, panels pushed past their original capacity, or original wiring that was never touched. The job types below are what we handle most often, and each one starts with a conversation about what the property currently has.
Connecting a generator to the home's electrical system is not a matter of running an extension cord to the panel. A transfer switch is what makes it safe, isolating the home from the utility line so power cannot feed back onto the grid while the generator is running. We handle the full electrical side: the wiring, the transfer switch installation, and connecting the generator to the circuits it needs to carry. For properties in the Pacific Northwest where extended outages are a real possibility, having the hookup done correctly means the generator is actually useful when it matters.
A Level 2 EV charger needs a dedicated 240-volt circuit, and whether the existing panel can support one depends on what the rest of the home is already drawing. We start with a load calculation before anything is run. If the panel has the capacity, we run the circuit to the garage or wherever the charger will mount. If it does not, we scope the panel upgrade as part of the same project. EV adoption across this region runs well ahead of most of the country, and the electrical infrastructure inside the home needs to keep pace with it.
High-draw equipment in a garage or workshop needs its own circuit sized to the load. A welder or air compressor pulling power from a shared circuit trips breakers and can damage the equipment over time. Dedicated circuits can be run for each piece of equipment, with the panel checked for headroom before anything is added and the correct outlet or connection point installed to match the load. This comes up regularly in properties where the garage has become a working space rather than just a parking spot.
Battery-operated detectors are a starting point, not a complete system. Hardwired smoke and carbon monoxide alarms connect to the home's electrical supply and communicate with each other so that an alarm in one room triggers the others throughout the house. We install hardwired detector systems, replace aging units, and add interconnected alarms to rooms where coverage is missing. For landlords and property managers, this is also one of the items that comes up during a safety inspection.
Recessed lighting and LED fixture upgrades are among the most common lighting requests we get. Replacing a single overhead fixture with a properly laid-out set of recessed lights changes how a room reads entirely, and the wiring involved depends on what is already in the ceiling and whether the circuit can carry the additional load. We also handle dimmer-compatible wiring, under-cabinet lighting in kitchens, and ceiling fan circuits where a single switch needs to be split to control the fan and the light separately.
When other electrical work is already scheduled, adding lighting to the same visit often makes sense. Running a new circuit while the panel is already open, or pulling wire while a wall is accessible during a rewire, costs less than returning for a second visit.
Exterior lighting covers porch and entry fixtures, motion-sensor and security lights, garage lighting, and outdoor outlets for a patio or garden area. Outdoor circuits involve weatherproof boxes and covers, correct conduit for any exposed runs, and grounding and bonding details that indoor work does not always require. Local permit rules decide which electrical jobs need an inspection, and we confirm what applies to your specific project before any conduit is run.
We'll sort the wiring and clean up after.
We are available every day from 8:30 AM to 11:00 PM, which covers most of the situations where waiting until a weekday morning is not a realistic option. Evening and weekend appointments are part of the regular schedule, not an exception.
For faults that will not wait, calling as early in the day as possible gives the best chance of getting work scheduled quickly. A burning smell near an outlet, a breaker that will not hold under normal load, or sparks when plugging something in are all situations worth calling about right away rather than scheduling for later in the week. We take short-notice work and electrical service scheduled without the runaround is what we aim for on every call.
For tenants and businesses that need to stay operational during the work, we talk through the scope on the phone so you know which circuits will be off and for how long before anyone arrives. That conversation happens before the visit is scheduled, not after.
In homes of this size and age, the main panel is most often in a garage, a utility room, or a basement. Subpanels, where they exist, are sometimes in a detached garage or a finished lower level. Knowing where the panel is before the visit means the diagnostic starts faster. If you are not certain where it is or whether the property has a subpanel, that is a useful thing to mention on the call.
Clear access to the panel is the single biggest factor. A panel blocked by storage, a locked room, or furniture pushed against the door adds time to every visit. For panel replacement or service-entrance work, the utility may need to disconnect power at the meter, and we coordinate that as part of scheduling. For a standard repair or circuit addition, access to the panel and to the affected outlets or fixtures is usually all that is needed. We keep you informed from diagnosis to final test so there are no gaps in what you know about the work.
The price for electrical work depends on what the job actually involves. What the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry a change are the things that move a quote up or down. A straightforward outlet replacement is a different scope from a panel upgrade with a load calculation and a permit.
When you call, we ask about the symptoms and the property so we can give you a price that reflects the actual job rather than a range wide enough to be meaningless. That price is confirmed before anything is scheduled. If what we find when we arrive changes the scope, we explain what changed and confirm a new price before proceeding. You decide whether to move forward once you have the full picture.
Pricing is straightforward and explained before we schedule. Ask what the quote covers and you get a straight answer.
We handle the same full range of electrical work across Snohomish County and the communities surrounding Edmonds. If you are in a nearby area and want to confirm coverage, call and we will tell you on the call. It is worth a look at the services page covering electrical work before you call.
We serve:
Permit requirements depend on the type of work and where it sits on the property. A panel replacement, a new circuit, and certain exterior installations commonly require a permit and inspection before the work is considered complete. We confirm what applies to your specific job before anything is scheduled so the work is not held up at the end.
A breaker that is warm under normal load is not unusual, but one that is hot or that feels significantly warmer than the others in the panel is worth investigating. Heat at a breaker can indicate a loose connection, an overloaded circuit, or a failing breaker. We check the breaker and the circuit it serves to find the cause.
Yes. Many older homes have wiring that is partially outdated but serviceable in the areas that have not been touched. We assess what is there and focus the work on the circuits that need attention rather than treating every job as a full rewire. If the inspection turns up conditions that make a broader update worth considering, we explain the options and let you decide.
Lighting upgrades, outlet additions, and circuit work are often worth scheduling together when the panel is already going to be open or when a wall is accessible during other work. Adding a dedicated circuit for a new appliance at the same time as a panel upgrade, or running exterior wiring while interior work is already underway, reduces the number of separate visits and the disruption that comes with each one. Mention everything you are considering on the call and we will tell you what makes sense to combine.
Yes, and it is usually easier to schedule it that way. If a new range, dryer, or other high-draw appliance is coming and the circuit or outlet is not already in place, getting the electrical work done before delivery means the appliance can be connected and tested as soon as it arrives. We can confirm what the circuit needs when you call.
Properties in a city like Edmonds often have a mix of original wiring and additions done at different points over the years, which can mean circuits that are undersized for current loads, panels that were never upgraded past the original service size, and GFCI or AFCI protection that was not required when the home was built but is now. A safety inspection is a useful way to get a clear picture of what the system actually looks like.
Access to a shared panel space usually involves the building manager or the property owner. We confirm who needs to be present or who can provide access before the visit is scheduled. If access is controlled by a third party, we work around their availability to find a time that keeps the job on track.
Whatever the issue is, from a circuit that keeps tripping to a panel that needs replacing to a generator hookup or an EV charger circuit, we handle it.
Call (425) 928-9789 and we will scope the job, give you a price, and get it on the schedule.
Short-notice electrical calls are welcome, and scheduling one is straightforward when you phone in. We are available from 8:30 AM to 11:00 PM, seven days a week.
Power restored. Code-compliant. Done right.
For every town we reach, see our full town list. Other towns where we take electrical work: Lynnwood, Mountlake Terrace, Shoreline, Kenmore, Bothell.
Every electrical job is different, and the right fix depends on what the wiring, the panel, and the circuits are actually doing. The table below covers the range of work we handle for homes and commercial properties in Edmonds and across Snohomish County. Each row gives you a quick read on what the service involves, who it fits, and what is worth knowing before you call.
| Service Type | What's Included | Best For | Good to Know |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular |
| Homes adding an EV charger, major appliance, or home office circuit | Panel upgrades are permitted and inspected. We confirm what the process looks like for your address before any work begins. |
| Breaker & Fuse Repair |
| Homes where a breaker trips repeatedly under normal load | A breaker that will not hold is often a sign of an overloaded circuit or a failing breaker, not just a nuisance to reset. |
| Whole-Home Surge Protection |
| Homes with EV chargers, home offices, smart appliances, or entertainment systems | A single surge event can damage multiple devices across the home at once. Panel-level protection covers every circuit simultaneously. |
Call (425) 928-9789 to get a quote and talk through what the job involves. We are available every day from 8:30 AM to 11:00 PM.
(425) 928-9789